#Signal web ui Bluetooth#

Level 3: level 2 and weak OFDM Orthogonal Frequency Division Multiplexing. However, increasing the level makes the AP slightly 'deaf' to its surroundings, causing the AP to lose a small amount of range.

#Signal web ui Bluetooth#

interferes (such as DECT or Bluetooth devices), the level can be increased up to level 5 for improved performance. 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. When performance drops due to interference from non- 802.11 802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). The default setting for this parameter is level 2. Wi-Fi can apply to products that use any 802.11 standard. Set a value for non- Wi-Fi Wi-Fi is a technology that allows electronic devices to connect to a WLAN network, mainly using the 2.4 GHz and 5 GHz radio bands. If you select the spectrum monitoring checkbox on this profile page, the AP will operate as a hybrid AP and scan the selected channel for spectrum analysis data. For example, if you entered 157 into the Channel field and selected the above option, radios using that profile would select 157 as the primary channel and 161 as the secondary channel.Ĩ0 Entering a channel number and selecting the 80 Mhz radio button selects a primary and secondary channel for 80 MHz Megahertz mode. When you use this option, the number entered becomes the primary channel and the secondary channel is determined by increasing the primary channel number by 4. This parameter includes the following channel number configuration options for 20 MHz Megahertz, 40 MHz Megahertz and 80 MHz Megahertz modes:Ģ0: Select this option to disable 40 MHz Megahertz mode and 80 Mhz mode and activate 20 MHz Megahertz mode for the entered channel.Ĥ0: Entering a channel number and selecting the 40 radio button in the WebUI selects a primary and secondary channel for 40 MHz Megahertz mode. The available channels depend on the regulatory domain (country). NOTE: This parameter is only available in the 2.4 Ghz radio profile. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. providing 256-QAM modulationĪnd encoding that allows for 600 Mbit/sec performance over 802.11n 802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. band Band refers to a specified range of frequencies of electromagnetic radiation. IEEE 802.11ac is an emerging VHT WLAN standard that could achieve physical data rates of close to 7 Gbps for the 5 GHz band. rate on 2.4 GHz Gigahertz. Very high throughput rates enable (256-QAM)Įnable/Disable VHT Very High Throughput. radio profile.Įnable/Disable High-Efficiency (802.11ax) features on the radio. The maximum data transfer rate is 54 Mbps. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. Networks using 802.11a operate at radio frequencies in the 5 GHz band.

NOTE: This parameter is only available in the 802.11a 802.11a provides specifications for wireless systems.

This option is enabled by default.Įnable/Disable very high-throughput ( 802.11ac 802.11ac is a wireless networking standard in the 802.11 family that provides high-throughput WLANs on the 5 GHz band.) features on the radio. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz.) features on the radio. Available options are:Įnable/Disable high-throughput ( 802.11n 802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. Table 1: 5 GHz/2.4 GHz RF Management Configuration ParametersĮnable transmissions on this radio band Band refers to a specified range of frequencies of electromagnetic radiation.Īccess Point operating mode.

In the Pending Changes window, select the check box and click Deploy Changes. Modify the desired settings, then click Submit.Ħ. Select either the 2.4 Ghz radio profile menu, or the 5 Ghz radio profile menu, then select the radio profile you wish to modify.Ĥ. In the Mobility Master node hierarchy, navigate to the System> Profiles tab.Ģ. management settings can be configured using the 2.4 GHz Gigahertz. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals.

Additional RF Management Settings in the WebUIĪdditional Advanced RF Radio Frequency.